Yealink DECT W56P Rebooting, Updating Firmware, Factory Reset

If your phone is malfunctioning or requires updates you or your phone system administrator may want to perform one of the following:


Restarting: This will bring the base station back to the its last configured state. 


Updating firmware: Firmware is the software that loads when the phone and base station is started and controls its functionality. Updating it to a newer version, when one is released, may resolve or improve phone performance issues. 


Factory reset: This erases the current configuration and apply the original configuration the phone was shipped with from the factory. You can reset the the base station or each individual handset. 


Restarting


Restarting the base station is usually a safe and easy method to resolve functionality issues. However, you may want to consult your phone system administrator first to make sure the issues are not related to network problems or other external causes. 

Also, since restarting the base station will cause any active or holding calls to be disconnected, you should alert any users connected to the base station before performing the reset. An easy way to do so is with the handset intercom feature.


To restart the base station via the handset: 


  • Press    to enter the main menu.

  • Select Settings>System Settings>Base Restart.

  • Enter the system PIN (default: 0000) and press the Done soft key.

The registration LED and network status LED go out simultaneously.  When the base station restarts successfully the LED indicators will illuminate solid green again.


You can also restart the base via the web user interface at the path Settings>Upgrade.


Firmware Upgrade


You can update the firmware on either the base or the handset. Firmware files can be downloaded from the Yealink support portal.  The file should be stored on a computer, mobile device, or network location that can be accessed by the web interface. 


You can check the current firmware installed on the base or a handset to see if an update is indeed required. 


  If you are using a multi-cell base station (Yealink W80 or W90) with your w56H handset refer to this article for instructions of how to perform a firmware updgrade.


To check the base station firmware via the handset:


  • Press    to enter the main menu.

  • Select Status>Base.

  • The screen displays the status information of the base station including the firmware version and IPv4 or IPv6 status, MAC address, device certificate status, RFPI and network information.

  • You can press    or    to scroll through the list and view the status information.

    You may need to provide some of this information, besides the firmware version, to your phone system administrator for additional phone support or maintenance.

To check the handset firmware via the handset:


  • Press    to enter the main menu.

  • Select Status>Handset.

  • The screen displays the status information of the handset including the firmware version and model, hardware version, IPUI code, SN code and area.

  • You can press    or     to scroll through and view the status information.

    You may need to provide some of this information, besides the firmware version, to your phone system administrator for additional phone support or maintenance.

Upgrading base and handset firmware via the web user interface:


  • Click on Settings>Upgrade.

  • If updating the base station firmware:

    • Click Browse next to the Select and Upgrade Firmware field to locate the required firmware file on your local system.

    • Click Upgrade next to the Select and Upgrade Firmware field.

    • A dialog box pops up to prompt “Firmware of the SIP DECT phone will be updated. It will take 5 minutes to complete. Please don't power off!”.

      Click OK to confirm the upgrade.

  • If updating the handset firmware:

    • Click Browse next to the Select and Upgrade Handset Firmware field to locate the required firmware file on your local system.

    • Click Upgrade next to the Select and Upgrade Handset Firmware field.

    • A dialog box pops up to prompt “Handset Firmware of the SIP DECT phone will be updated. It will take 5 minutes to complete. Please don't power off!”.

      Click OK to confirm the upgrade.

The upgrading process will take a few minutes. The power indicator LED on the base station flashes during the firmware upgrading process.


Once the base station firmware has been successfully upgraded, the base station reboots automatically. The handset will perform an auto registration to the base station.


Factory Reset


  It is advisable you contact us  (if you have an account with us) or your phone system administrator before attempting a factory reset to see if the issues with your phone may be resolved without it and to ensure your phone can be properly provisioned and configured if a reset is indeed required.


You can factory reset either the base station or each individual handset.


Factory Reset  Base


You can reset the base station from the either the base station or a handset. Reseting from the base station will clear all settings while resetting from a handset will keep the system PIN and handset registration. 


To reset the base station from the base station:

  • Disconnect the power adapter.

  • Long press the paging key and reconnect the power adapter.

  • When base station finishes resetting, the power indicator LED, network status LED and registration LED illuminate in sequence.

  •  System PIN and all individual settings are reset to factory defaults. Handset registrations will also be cleared after base station reset.

To reset the base station from the handset:


  • Press   to enter the main menu.

  • Select Settings>System Settings>Base Reset.

  • Enter the system PIN (default: 0000), and then press the Done soft key.

  • Highlight Reset to factory, and then press the OK soft key.

  • The resetting process may take a few minutes. Do not power off until the base station starts up successfully.

    The power indicator LED and network status LED on the base station slow flash in sequence during the resetting process. Indicator LEDs on the base station illuminate solid green after startup.

    Resetting the base station will will clear all individual settings (e.g., directory and account registrations). Handset registrations and the system PIN will not be reset to factory defaults.

You can also reset the base station via the web user interface at the path: Settings>Upgrade.  


Factory Reset Handset


Resetting the handset will not overwrite the settings for directory, call history, voice mail and the handset registration to the base station. Other customized settings will be reset to factory settings . 


To reset the handset via the handset:


  • Press   to enter the main menu.

  • Select Settings>System Settings>Handset Reset.

  • The screen prompts “Reset handset to default?”.

    Press the Yes soft key to reset the handset or the No soft key to cancel.

Did you find it helpful? Yes No

Send feedback
Sorry we couldn't be helpful. Help us improve this article with your feedback.