1. Teleboard | Support Center
  2. Solution home
  3. Yealink T4 Series Phones User Guides – T43U, T46U, T48U
  4. Yealink SIP-T46U
Open navigation

Yealink SIP-T46U Rebooting, Updating Firmware/configuration, Factory Reset

If your phone is malfunctioning or requires updates you or your phone system administrator may want to perform one of the following:


Rebooting: This will bring the phone back to  its last configured state. It is also required sometimes when TeleConsole settings have been updated such as after modifying the TeleConsole BLF settings.


Updating configuration: Settings or configuration changes made by Telebroad or your system administrator are applied to the phone when you trigger a configuration update. Depending on the updated settings this may or may not require you to restart your phone.


Upgrading the firmware: Firmware is the software that loads when the phone is started and controls its functionality. Upgrading it to a newer version, when one is released, may resolve or improve phone performance issues. 


Factory resetThis erases the current configuration and applies the original factory configuration the phone was shipped with. An admin password is required, but a certain configuration setting makes it possible to bypass this and reset without a password.


Rebooting Your Phone


Rebooting your phone is usually a safe and easy method to resolve functionality issues. However, you may want to consult your phone system administrator first to make sure the issues are not related to network problems or other external causes. 


To reboot your phone:


  • Do one of the following:

    • On the phone, navigate to Menu>Basic>Reboot.

    • Long press Cancel () on the keypad when the phone is idle.

    • Access the phone via the web user interface as explained here.

      Select the Settings tab on the top and select the Upgrade tab from the side tab.

      Click Reboot.

  • Press or select OK when prompted to confirm that you want to reboot the phone.

Updating Configuration


Changes in the system or network of your office may cause problems with the functionality of your phone. To restore compatibility or simply to apply new settings for improved workflow, your system administrator may ask you to update the phone's configuration after he has prepared the relevant configuration file. 


When you trigger the configuration update the new configuration file is downloaded from a provisioning server to the phone's flash memory and the update process is completed automatically. 


To update the phone's configuration:


  • Do one of the following:

    • Navigate to Menu>Basic>Update Configuration.

    • Long press   (redial) when the phone is idle.

  • Select OK when prompted by a "Provision now?" message to approve the update.

Upgrading the Firmware


Firmware files can be downloaded from the Yealink support portal. The downloaded file should be stored on a computer or network location that can be accessed by the web user interface. 


Before upgrading to the latest firmware you should read the related firmware notes and possibly consult with Yealink's support to ensure there are no compatibility issues or other potential conflicts. If such issues or conflicts do happen after an upgrade you may need to downgrade to a previous firmware version or perform a factory reset.


Checking the Current Firmware Version


You can check the current firmware version installed on the phone to see if an update is indeed required. 


To check the firmware version from the phone: 


  • Press    or press Menu>Status.

  • Press    or    to scroll through the list to view phone status information.

    The firmware version is the 3rd item.

    You may need to provide some of the information listed here, besides the firmware version, to your phone system administrator for additional phone support or maintenance.

To check the firmware version via the web user interface:

 

  • Access the phone via the web user interface as explained here.

  • The firmware version is the first item found under the Status tab (the first page of the web user interface.)

Upgrading the Firmware


When upgrading the firmware it is important that you do not close or refresh the browser running the web user interface. Also, during the upgrade, you must not close any network connections on the device running the web user interface or power the device off. 


To upgrade the firmware via the web user interface: 


  • Access the phone via the web user interface as explained here.

  • Select the Settings tab on the top and select Upgrade from the side menu.

  • Click Browse to locate the firmware file you downloaded from Yealink on your local system.

  • Click Upgrade to upgrade the firmware.



    The browser prompts “Firmware of the SIP Phone will be updated. It will take 5 minutes to complete. Please don't power off!”.

  • Click OK to confirm upgrading.

The phone will reboot once the upgrade is finished.


Factory Reset


Factory reset is only recommended after you have tried all other troubleshooting suggestions since it will delete all your personal configuration settings and reset them to the factory defaults.

  It is advisable you contact us  (if you have an account with us) or your phone system administrator before attempting a factory reset to see if the issues with your phone may be resolved without it and to ensure your phone can be properly provisioned and configured if a reset is indeed required.


To perform a factory reset from your phone:


  • Do one of the following:

    • Navigate to to Menu>Advanced>Reset Config.

      If prompted for password enter the default password ("admin") or the current phone's admin password.

      Select the Reset to Factory and then press Reset.

    • If enabled by your phone system administrator, when the phone is idle you can long press the OK key on the keypad for about five seconds. Enter the default password ("admin") or the current phone's admin password.

  • Press OK to confirm resetting the phone.

  • The screen displays “Welcome Initializing…Please wait”.


The process will take a few minutes. Do not power off until the phone has started up successfully.


If you forgot or don't know the admin password of the phone you can contact us or your phone system administrator to see if we or he have a record of the current admin password. 


It is also possible to have the phone's settings changed so it does not require a password when you long press the OK key (the specific configuration file setting is “features.factory_pwd_enable=0” ). After the setting is changed update your phone's configuration. You should now be able to reset your phone without being prompted for a password. After the reset, the default password ("admin") should work. 


To perform factory reset via the web user interface:


  • Access the web user interface as explained here.

  • Select the Settings tab on the top and select Upgrade from the side menu.

  • Click Reset to Factory Settings in the Reset to Factory field.

  • Click OK to confirm when the web user interface prompts “Do you want to reset to factory?”.

  • The phone will be reset to factory successfully after startup.

    The process may take a few minutes. Do not power off until the phone starts up successfully.

Was this article helpful?

That’s Great!

Thank you for your feedback

Sorry! We couldn't be helpful

Thank you for your feedback

Let us know how can we improve this article!

Select atleast one of the reasons

Feedback sent

We appreciate your effort and will try to fix the article